Project "Get my printer printing reliably"

Post Reply
User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Project "Get my printer printing reliably"

Post by Jubbp » Sun Oct 28, 2018 1:00 pm

I've been frustrated by my Felix 3 Printer for several years. It appears it requires a baby sitter to print reliably.

I would like my printer to print reliably and consistently without constant attention

I'll be updating this thread with my efforts.

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Sun Oct 28, 2018 1:03 pm

as an example, the image below is a recent piece of a failed print.
IMG_0896.jpg
IMG_0896.jpg (21.54 KiB) Viewed 33001 times
Ignore the roughness at the bottom, thats where I removed some supports. The main issue is the patchy printing thoughout the print.

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Sun Oct 28, 2018 1:15 pm

Another example from the same project.
IMG_0897.jpg
IMG_0897.jpg (31.04 KiB) Viewed 33001 times

DJCoopes
Mini-Maker
Posts: 40
Joined: Sat May 26, 2018 11:38 am
Location: Busselton
Contact:

Re: Project "Get my printer printing reliably"

Post by DJCoopes » Wed Feb 20, 2019 1:59 pm

Does your printer's extruder have fans attached to it? this could help with layer adhesion and webbing.
10 poke 53281,0
20 poke 646,5
30 poke 53280,0
40 poke 647,0
50 print " **** commodore 64 basic v3 ****"
60 print " "
70 print " 64k ram system 38911 basic bytes free"
80 print " "
90 print "ready."

parkview
Guru Maker
Posts: 603
Joined: Tue Jun 24, 2014 8:25 pm
Location: Busselton
Contact:

Re: Project "Get my printer printing reliably"

Post by parkview » Fri Feb 22, 2019 3:34 pm

Hi DJ,

three of us have the same printer. It comes with a hot end fan and left and right cooling fans as it extrudes. Phillip brought it along last meeting and found that the extruder drive current was out. A tweak later on the motor drive current and it was working well.

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Fri Feb 22, 2019 4:06 pm

Phillip brought it along last meeting and found that the extruder drive current was out
Yes, Thanks for the help, I'll need to find some time to update the thread.

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Sat Feb 23, 2019 11:23 am

So I took my Felix 3D Printer along to the February South West Makers meeting st the Eaton Library. I had been speaking with Stephen about it at the December meeting.

A couple of quick test prints and Stephen, Paul and Rob were onto the problem quickly.

The problem was under extrusion and while printing we were easily able to stop the flow by holding the filament back and hearing the infamous "click".

We checked the tension on the print head but that was up as high as it would go. Stephen then hit the jackpot.

The current delivered to the stepper motor was insufficient to push the filament through the head and the stepper motor was missing steps as a result. :roll:

A quick adjustment to the driver on the control board and the print head was extruding filament like a champ. :D

Image
Image credit to Paul from the SWMakers Blog http://www.swmakers.org/blog/sw-makers- ... on-meeting

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Sat Feb 23, 2019 11:37 am

Of course, there is more to the story.

When I returned home with the printer, I still had a few issues.

Immediately, I had issues with serious under extrusion.

I had to revisit my slicer settings in Simplify3D. During my troubleshooting I had made changes which had to be reconfigured.

As it was under extruding again, I tried upping the extrusion factor to increase the flow of filament. This has the opposite affect to that which I was expecting. Extrusion almost stopped all together. I finally worked out that the drive gear was actually moving too fast and was gouging the filament and not pushing properly.

I reduced the extrusion back to 100% and I'm now printing my first complex item in several months. I have manually reduced the flow rate down to 90% during this print after a couple of under extrusion issues and the print appears to be coming along nicely.
A8576DBE-E0D4-4D29-9CB1-FF365E59B411.jpeg
A8576DBE-E0D4-4D29-9CB1-FF365E59B411.jpeg (83.92 KiB) Viewed 32733 times

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Sun Feb 24, 2019 10:39 am

Closing in on the optimum slicer settings
D5A0D78A-2A39-40E3-A014-34C6E12C7D71.jpeg
D5A0D78A-2A39-40E3-A014-34C6E12C7D71.jpeg (78.89 KiB) Viewed 32727 times
812576C7-EA7B-4878-B6F3-83D64624718C.jpeg
812576C7-EA7B-4878-B6F3-83D64624718C.jpeg (74.56 KiB) Viewed 32727 times

DJCoopes
Mini-Maker
Posts: 40
Joined: Sat May 26, 2018 11:38 am
Location: Busselton
Contact:

Re: Project "Get my printer printing reliably"

Post by DJCoopes » Mon Feb 25, 2019 10:09 am

Has anyone had any experience using CURA with their 3d printer? Just wondering.
Last edited by DJCoopes on Tue Mar 19, 2019 4:35 pm, edited 1 time in total.
10 poke 53281,0
20 poke 646,5
30 poke 53280,0
40 poke 647,0
50 print " **** commodore 64 basic v3 ****"
60 print " "
70 print " 64k ram system 38911 basic bytes free"
80 print " "
90 print "ready."

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Mon Feb 25, 2019 10:22 am

Has anyone had any experience using CURA with their 3d printer?
I haven't had any experience with it but I will soon be looking into it as it's the inbuilt slicer in the OctoPrint. Which, by the way, is the reason I need my printer printing reliably, I want to be able to set it and forget it during prints.

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Mon Feb 25, 2019 10:23 am

PS, I have to take some more photos from yesterdays efforts. The Benchy is looking much nicer after some more tweaking of the Slicer

parkview
Guru Maker
Posts: 603
Joined: Tue Jun 24, 2014 8:25 pm
Location: Busselton
Contact:

Re: Project "Get my printer printing reliably"

Post by parkview » Mon Feb 25, 2019 11:52 am

A lot of us use Simplify3D: https://www.simplify3d.com/ but experimented with OctoPrint a few years ago.

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Sun Mar 03, 2019 11:51 am

E37E05D4-85B6-4424-9EB0-B63C79D20A65.jpeg
E37E05D4-85B6-4424-9EB0-B63C79D20A65.jpeg (84.39 KiB) Viewed 32703 times
Well it seems like I’m getting somewhere. Vaze printed in “vase mode”. Looks almost perfect.

parkview
Guru Maker
Posts: 603
Joined: Tue Jun 24, 2014 8:25 pm
Location: Busselton
Contact:

Re: Project "Get my printer printing reliably"

Post by parkview » Sun Mar 03, 2019 2:20 pm

Looks great form the picture! Does it hold water?

User avatar
Jubbp
Master Maker
Posts: 209
Joined: Sun Jun 22, 2014 8:15 pm
Location: Bunbury WA
Contact:

Re: Project "Get my printer printing reliably"

Post by Jubbp » Sat Mar 30, 2019 8:21 pm

Things I learnt today.

I was trying improve my top layers. I have always been a bit stingie on the infill and normally print at about 20% infill.

Today I tried 30% and found a great improvement.
IMG_1101.jpg
IMG_1101.jpg (173.39 KiB) Viewed 32506 times

User avatar
rick
Newbie
Posts: 9
Joined: Tue Aug 24, 2021 7:32 pm

Re: Project "Get my printer printing reliably"

Post by rick » Sun Jan 09, 2022 5:26 pm

Looking good Jubbp the quality of the prints are getting better and better.

I've been working on my ender over the holidays and its had a few upgrades, still fighting with it to get better quality out of it.

"DJCoopes I've been using cura since I started with my ender, what you stuck on?"

Post Reply