Page 1 of 1
Perth Curtin University Robofair 2015
Posted: Wed Aug 19, 2015 10:27 pm
by parkview
Hi, it's on again:
Event: Robofair 2015
Date: Sunday 6th of December 2015
Time: 10 am – 2 pm
Location: Engineering Pavilion (Building 215)
Curtin University
Kent Street, Bentley
Same place, same time, in Dec. instead of November, so it could be a bit warmer.
PM me, or email me if your interested in attending. If you haven't been before, I recommend a visit. Lots of robotics, drones, Lego robotics and science things.
Re: Perth Curtin University Robofair 2015
Posted: Fri Aug 28, 2015 7:31 pm
by parkview
2 x tables booked for 4 people, so we have half a table each.
Artifactory, West Coast Makers and Enkel will now all be attending as well. It should be an interesting room!
Re: Perth Curtin University Robofair 2015
Posted: Fri Nov 06, 2015 4:44 pm
by BeJay
I might not be able to make it this year
I have to do a bit of FIFO for work, so I will let you guys know a bit closer to the date, but at this stage it overlaps
Cheers
Bj
Re: Perth Curtin University Robofair 2015
Posted: Sat Nov 07, 2015 6:17 am
by seaton
Bugger!
Re: Perth Curtin University Robofair 2015
Posted: Fri Nov 27, 2015 7:18 am
by BeJay
Ok, looks like I 'm going to be back by Sunday now, so what is the plan of attack with this year?
I don't have much new stuff to show, as the XYZCarve I made i too big to fit in the car! I did make a plywood case for my Pi powered SDR, but it's not finished yet. I can bring it anyway. I was hoping to make some more kid interactive things, but I just haven't found the time since last year.... crickey!
Re: Perth Curtin University Robofair 2015
Posted: Fri Nov 27, 2015 7:26 am
by parkview
I hope to be there at around 08:00 - to claim the space. We should have half a table each and a pin up board (unverified). See last nights email with PDF attachment that shows the floor plan.
I don't think it matters what you bring. With 2000 odd people walking past, there will be someone that's interested in what you have. This year I am targeting other Makers, not the kids.
Re: Perth Curtin University Robofair 2015
Posted: Tue Dec 01, 2015 5:06 pm
by BeJay
I was going to cut a sign tomorrow for robofair, and was wondering if you guys have a decided logo and a vectorised SVG of it I can cut?!
Re: Perth Curtin University Robofair 2015
Posted: Wed Dec 02, 2015 9:25 am
by Jubbp
Thanks Bejay,
but we haven;t really decided on the logo as yet
. Maybe something we should finally get done soon.
Re: Perth Curtin University Robofair 2015
Posted: Wed Dec 02, 2015 9:39 am
by Jubbp
Having said that, This is what I do have.
https://dl.dropboxusercontent.com/u/221 ... dalion.svgSee if you can use that.
Re: Perth Curtin University Robofair 2015
Posted: Wed Dec 02, 2015 9:41 am
by BeJay
I'll give it a go!
edit: Here it is...
It's 300 x 300mm so not too bad. Should have used MDF for it's forgiveness, but thought I'd wing it with ply from Bunnings
Re: Perth Curtin University Robofair 2015
Posted: Sun Dec 06, 2015 6:05 pm
by BeJay
Re: Perth Curtin University Robofair 2015
Posted: Sun Dec 06, 2015 10:00 pm
by parkview
Re: Perth Curtin University Robofair 2015
Posted: Sun Dec 06, 2015 10:01 pm
by parkview
and a few more:
- watercolorbot.jpg (31.8 KiB) Viewed 19371 times
- setting up.jpg (57.35 KiB) Viewed 19371 times